NEw Hot Rod motor is in WOOT WOOT

[THE MALIGOON]

Big shout out to CUTLASSJESSE for lending me a hand with this today


Well the new 350 is in WITH LONG tubes from a G-BODY 82 cutlass they were a direct bolt up ..........Lay them in the engine bay wiggle them around while you bolt the trans back to the motor, then just pull them all the way forward and bolt them up...... NO CLEARANCE ISSUES WHAT SO EVER

Pics are up loading as I type this

http://i239.photobucket.com/albums/ff99/hotrod74malibu/0e9ca58b.jpghttp://i239.photobucket.com/albums/ff99/hotrod74malibu/d22d165a.jpghttp://i239.photobucket.com/albums/ff99/hotrod74malibu/bda06cce.jpghttp://i239.photobucket.com/albums/ff99/hotrod74malibu/5afad0a4.jpg

[THE MALIGOON]

Yes i said 82 g-body cutlass headers directly bolt up to our car with no mods


EDIT: finding out what brand of headers sorry forgot that part LOL

These were flowtech's header part number Flowtech 11150FLT these are a direct bolt up following the way in first post

http://static.summitracing.com/global/images/prod/large/big-11150flt_w.jpg

[texxas8902]

Maybe you should post a header brand name before making a blanket statement that G body headers will fit our cars... just saying...:D new engine looks great by the way.

[mdkingsley]

Looks like it should be fun, and good info on the G-Body headers.

[1977 Cutly]

Looks great! I love those valve covers.... Keep us posted on the progress and keep up the good work

[W451973]

Give us some details about whats been done to the motor.

[THE MALIGOON]

its on the other post buddy sorry will bring it here ...............my introduction post is where I meant.

350 olds fresh rebuild, has not been bored but its got new bearings in it rod and main new set of rings head gaskets Lunati bracket master 2 cam kit, double roller timing chain edlebrock 550 (switched to my 750) on it new set of headers (FLOWTECHS) new set of lifters all new gaskets from carb to pan new starter its got the hei distributor ((ADDED MY ACELL SUPER COIL TO IT)and taylor wires and just have to clean it and repaint the crazy colors it has remnants of LOL

Some work has been done the heads and manifold #8 heads (not the best I know but they have been worked a little to perform better) I will post a video (once I get everything started up will switch to my Holley 750 Dual feed carb with a proform center) I want to get the thing running in the car first then adjust for the Holley after installation

[W451973]

Sounds good. And if thats a 73-76 short block then it'll have the higher compression pistons so putting on some earlier heads will really make a big difference. What happened to the 455 plan ?

[THE MALIGOON]

yes its a 73 block and the 455 wasn't gonna happen till next year after I saved the money getting this motor was a fluke basically the guy that sold it to me wanted a 455 and I had it just sitting in corner collecting dust till I had saved enough money for the build as I wanted it.

So that was the end of the 455 story and this motor was a plug already for he just got done rebuilding it and doing all the other stuff to it, and he offered to straight across the board trade so I jumped on it.

And as far as the heads I am gonna do the BBO head trick that I have been reading about and it will really wake this monster up even more

[THE MALIGOON]

new motor is in and running

http://www.youtube.com/v/wkBB7SNa5FE

[zates]

I was on edge for a second after you kicked the starter - but she's running and sounding great fantastic. And it doesn't appear that it cost you a major fortune. I'll drive mine down to Byron and leave it with you if you want another project!!!

[THE MALIGOON]

yea I twisted the dist a lil bit when i installed the motor and forgot to urn it back LOL

But yea it is reset now and starts on first crank ......well after a few pumps of gas anyways, And as far as your car bring it on I will have heat this winter in garage so can finally get more done.

[grumpy hvacr]

I have had a very bad day at work. I saw your video and all the stress and B.S. just went away. Thank you. I feel better now.

[THE MALIGOON]

OK that has to be the best post I have had to it so far LMAO glad I could ease your stress LOL

[zates]

Anthony,

You're about 45 min. from Durand. My kid occasionally plays there at Cases II in Durand. If you like good blues guitar and feel like a nice ride, look him up. Here's the band link:
http://www.myspace.com/playgroundofsound

Looks like they're playing on December 31. Hey... and no selfless promotion from my end!! :D:D

Pete

[THE MALIGOON]

I know right where its at been thru there on more than one occasion matter of fact was just in Durand last week to pick up some keystone classic wheels

and the band sounds good and that guys Voice is killer sounds real goodhttp://r18.imgfast.net/users/1813/58/83/10/smiles/852610.gifhttp://r18.imgfast.net/users/1813/58/83/10/smiles/501781.gifhttp://r18.imgfast.net/users/1813/58/83/10/smiles/852610.gif

[THE MALIGOON]

Anthony,

You're about 45 min. from Durand. My kid occasionally plays there at Cases II in Durand. If you like good blues guitar and feel like a nice ride, look him up. Here's the band link:
http://www.myspace.com/playgroundofsound

Looks like they're playing on December 31. Hey... and no selfless promotion from my end!! :D:D

Pete

Hey and ask him to burn me a few copies of his stuff I would jam that in garage while working on the car got a great sound to them

[ragz442]

Sounds good, you plan on racing it?

[THE MALIGOON]

well the dragstrip IS UNDER 5 minutes to drive there LOL so a possibility

[zates]

Hey and ask him to burn me a few copies of his stuff I would jam that in garage while working on the car got a great sound to them

They've been in the studio, but haven't had the cash to complete a CD yet. I might have some loose stuff on my hard drive that I could burn you. Let me look around.

[THE MALIGOON]

sweet buddy thanks